Th-42ph10ak manual

Please refer to those materials packaged with your product. Panasonic and its parent and affiliates are not responsible for any loss or damage Including data corruption, interruption of operation, lost business information, etc. We reserve the right to revise update or suspend access to this site without prior notice. Acrobat Reader is available free from the Adobe website whose link is on the left.

Added Removed. Please read and accept the terms of use before downloading this document. I accept the terms of use below.

Terms of Use 1. Contents of the Operating Instructions Site a. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

If water droplets get inside the unit, operating problems may result. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

Check that you have the Accessories and items shown. For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Precaution on battery use. Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

Do not combine a used battery with a new one. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. When connecting the speakers, be sure to use only the optional accessory speakers. However, the image will not be displayed properly if the signals exceed 1, lines. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

Use a computer application such as programming language software. Refer to the documentation for the computer application for details. The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order.

If there are no parameters, then the parameter signal does not need to be sent. From the second time on, language selection can be done from the setup menu. Set with the remote control. Buttons on the main unit are unavailable for this setting. From the second time on, the screen shown below is displayed for a while setting condition is an example.

Press the button on the remote control to turn the Plasma Display off. Power Indicator: Red standby. Press the button on the remote control to turn the Plasma Display on. Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode. During operation of the power management function, the power indicator turns orange in the power off state. These buttons can only display the slot which is installed. If you press the button whose slot is not installed, it automatically displays the current input signal.

The function that darkens the screen slightly is activated to prevent image retention see page 46 , this function is not the perfect solution to image retention. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes off timer cancelled each time the button is pressed. The off timer is cancelled if a power interruption occurs. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. THPS9 The illustration shown is an image. Do not defeat the purpose of the grounding plug. Important Safety Instructions 1 Read these instructions. Dear Panasonic Customer Welcome to the Panasonic family of customers.

Table of Contents Important Safety Instructions Note: Do not allow a still picture to be displayed for an extended period, as this can cause permanent image retention to remain on the Plasma Display. When using the Plasma Display Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.

Be sure to disconnect all cables before moving the Plasma Display. Clean the power cable regularly to prevent it from becoming dusty. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display.

Do not place any objects on top of the Plasma Display. Do not cover the ventilation holes. Transport only in upright position! Do not use any power supply cord other than that provided with this unit. Securely insert the power cord plug as far as it will go.

Do not handle the power cord plug with wet hands. If problems occur during use If a problem occurs such as no picture or no sound , or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately. Maintenance The front of the display panel has been specially treated.

If the cabinet becomes dirty, wipe it with a soft, dry cloth. Pull and hold the hook, then 2. Insert batteries - note correct 3. Replace the cover. Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Observe the following precautions: 1. Plug the AC cord into the display unit. Plug the AC cord until it clicks. Note: Make sure that the AC cord is locked on both the left and right sides.

To tighten: To loosen: Push the catch Pull 2 Pull. Signal Name Pin No. Communication parameters Signal level RSC compliant Synchronization method Asynchronous Baud rate bps Parity None Character length 8 bits Stop bit 1 bit Flow control - Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order.

Fix the AC cord plug securely to the Plasma Display. Note: Set with the remote control. Power Indicator: Green Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode. Note: During operation of the power management function, the power indicator turns orange in the power off state. N button see page 20, 23, 24, 25 POS. SOUND button see page R button see page 17 Press the R button to return to previous menu screen.

Channel Adjustment This button cannot be used for this model. This displays an enlargement of the designated part of the displayed image. The MENU button on the unit can also be pressed. To POS. You can only view or download manuals with. Sign Up and get 5 for free.

Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need.