Damag electrical tool

Use clamps, a vice or other devices to hold and support the piece being worked on, when practical to do so. This will allow you to use both hands for better control of the tool and will help prevent injuries if a tool jams or binds in a work piece.

Use only approved extension cords that have the proper wire size gauge for the length of cord and power requirements of the electric tool that you are using. This will prevent the cord from overheating. For outdoor work, use outdoor extension cords marked "W-A" or "W".

Suspend power cords over aisles or work areas to eliminate stumbling or tripping hazards. Eliminate octopus connections: if more than one receptacle plug is needed, use a power bar or power distribution strip that has an integral power cord and a built-in overcurrent protection. Pull the plug, not the cord when unplugging a tool. Pulling the cord causes wear and may adversely affect the wiring to the plug and cause electrical shock to the operator.

Follow good housekeeping procedures — keep the work area free of clutter and debris that could be tripping or slipping hazards. Keep power cords away from heat, water, oil, sharp edges and moving parts. They can damage the insulation and cause a shock. Ensure that cutting tools, drill bits, etc. Store tools in a dry, secure location when they are not being used.

Do not wear gloves, loose clothing or jewelry while using revolving power tools. Tie back long hair or wear appropriate hair protection to prevent hair from getting caught in moving parts of equipment. Do not use a tool unless you have been trained to use it safely and know its limitations and hazards.

Avoid accidental starting by ensuring the tool is turned off before you plug it in. Also do not walk around with a plugged-in tool with your finger touching the switch. Do not disconnect the power supply of the tool by pulling or jerking the cord from the outlet. Do not leave a running tool unattended. Do not leave it until it has been turned off, has stopped running completely, and has been unplugged. Do not use electric tools in wet conditions or damp locations unless tool is connected to a ground fault circuit interrupter GFCI.

Because power tools are so common in construction, workers are constantly exposed to a variety of hazards. The very tool that makes their job easy and efficient may one day be the cause of a tragic accident. It is good to be reminded of common-sense safety practices. Electrical - Hazards Power Tools. Power Tools Because power tools are so common in construction, workers are constantly exposed to a variety of hazards.

For example, scorching, burn marks and staining are all signs that equipment is overheating and should be taken out of use. Damage to casings, covers, cables, and plugs are also signs of a problem.

Raise awareness of electrical risks with the free electrical safety toolbox talk. Users of power tools need to pay attention and concentrate on the activity and safe use of the tool, do not use when tired or under the influence of drugs or alcohol. Power tools are as the name suggests powerful tools. A momentary lapse in concentration can result in serious injury.

Take care not to overreach and keep proper footing to avoid losing control. PPE is your last line of defence against harm. Hazards to the user include projectiles, contact, noise, vibration and entanglement. Always wear appropriate PPE to protect you from the specific hazards presented by power tools, such as dust exposure and projectiles. PPE such as goggles, dust mask, gloves, hard hat, and safety boots should be worn where appropriate.

Depending on the noise levels involved, it may be necessary to wear hearing protection during your use of the tool. Need help convincing your team why PPE is important? Remember, use the correct power tool for the task and take defective tools of use for replacement or repair. Good use of power tools will increase productivity and improve safety, poor use of power tools with increase risks and reduce productivity.

Need help? Use the power tools risk assessment template to get your paperwork in place and give your team the information they need. This article was written by Emma at HASpod.

Search hundreds of health and safety documents ready to edit and download for your construction projects. Pinch point hazards are common in many workplaces, and especially in construction and manufacturing. A pinch might not sound too severe, but pinch points can cause life-changing injuries, and in the worst cases, they can be fatal.

But what is a pinch point? And how can you spot these hazards? When you are planning a construction project, you are going to need to provide some temporary facilities.

Used correctly, these facilities will keep your site safe and productive. Here's a list of 10 temporary facilities you need on your construction sites.

Technology has advanced at record speed over the past 20 years. We've gone from games of snake to running an entire business from your mobile phone. Let's take a look at the remote technology you can use for better construction health and safety. Training Plan Access to all courses with no limits.

Talks Plan Get daily health and safety talks. Free Tools Free and simple health and safety tools. Blog Best practice and safety guidance. Log In Support Contact Us.